Technology, energy, agriculture transport AIC

Y. Paladiichuk – PhD, Associate Professor of the Department of “Agroengineering and technical service” of

Vinnytsia National Agrarian University (3, Sunny St., Vinnytsia, 21008, Ukraine, e-mail:

rewet@vsau.vin.ua).

L. Shvets – PhD, Associate Professor of the Department of “Agroengineering and technical service” of

Vinnytsia National Agrarian University (3, Sunny St., Vinnytsia, 21008, Ukraine, e-mail: shlv0505@i.ua).

D. Kondratuk – PhD, Associate Professor of the Department of “Agroengineering and technical service” of

Vinnytsia National Agrarian University (3, Sunny St., Vinnytsia, 21008, Ukraine, e-mail:

kondratuk@vsau.vin.ua).

PROCESSING OF DEEP SURFACES WITH COMBINED TREATMENT

When broaching deep openings, especially long-length casing of hydraulic cylinders, practically

makes it cutting with two-sided shaving grooves of normal length due to insufficient strength of the tool

for tension. For the forced separation of the shear layer at the stroke, it is proposed to create, on the

working surface of the part, full regular macroreliefs with the help of deformation and cutting stretching.

The technological properties of the full control of the macro-relief will allow the traditional chip-split

scrubs to be abandoned on the rough, semi-roughing and finishing blades of the drag, allowing for the

entire length of the cutting loop to be put into operation. The study of the formation of complete regular

macroreliefs has shown that they can also be used effectively in solving technological problems, in

particular for the forced separation of the let down into cutting, fulfilling its basic service functions. It has

been established that the free formation of a cutting roll when it is stretched by a tool with a flat front

surface affects the thickness of the cut, the properties of the processing material, as well as the degree of

deformation strengthening. The dimensions of the cutting roll and the ability of the latter to form a flat or

spatial spiral is of great importance for those cutting processes whose kinematics does not allow for the

free evacuation of chips from the chipping zone. First of all it concerns internal cutting, since the

diameter of the cutting roll is the determining factor for the permissible degree of filling of the cutting

groove.

Key words: broaching, deformation, macrorelief, shavings, relief formation.

F. 5. Fig. 1. Ref. 12.

References

[1] DSTU 2860:1994 (1995) Nadiinist tekhniky. Terminy ta vyznachennia [Reliability of technology.

Terms and definitions]. Kiev: Derzhstandart Ukrainy [in Ukrainian].

[2] Tkachuk, N. A., Dyachenko, S. S., Posvyatenko, E. K. and others (2018) Kontynualnaia y dyskretnokontynualnaia

modyfykatsyia poverkhnostei detalei: monohrafyia [Continuous and discrete-continual

modification of parts surfaces: Monograph]. Kharkov: Planeta-Prynt [in Russian].

[3] ISO14577–3:2015 (2015) Metallic materials. Instrumented indentation test for hardness and materials

parameters. Part 3: Calibration of reference blocks. Geneva: ISO Publ.

[4] Trent, E. M. (1984) Metal Cutting. London, Boston, Durban, Singapore, Sydney, Toronto, Wellington,

Butterworts.

[5] Enahoro, H. E. (1966) Effekt of cold – working on chip formation in metal cutting, 13, 251 – 261, Ann.

C.S.R.P.

[6] Wagner, H. В., Lourie, O., Zhou, X. F. (1999) Macrofragmentation and macrofragmentation

phenomena in composite materials, 1, 59 – 66, Compos A.

[7] Oliver, W. C., Pharr, G. M. (2004) Measurement of hardness and elastic modulus by instrumented

indentation: Advances in understanding and refinements to methodology, J., V.19, 1, 3 – 20, Mater.

res.

[8] Marchenko, A. P., Tkachuk, M. A., Sobol, O. V. and others (2017) Innovatsiini tekhnolohii

kompozytsiinoho zmitsnennia poverkhni elementiv vyrobiv dlia oboronnoi ta enerhetychnoi haluzei

[Innovative technologies of composite strengthening of surface elements of products for the defense and

power industries], 1, 234 – 236, Mechanics and machine building [in Ukrainian].

[9] Chatterjee-Fisher, R., Eisel, F. V., Hofmann R. and others (1990) Azotyrovanye y karbonytryrovanye:

monohrafyia [Nitriding and carbonitriding: мonograph.] Moscow: Metallurhyia [in Russian].

[10] Falub, C. V., Karimi, A., Ante, M., Kalls, W. (2007). Interdependence between stress and texture in

arc evaporated Ti-Al-N thin dilms, 12 (201), 5891 – 5898, Surface and Coatings Technology.

[11] Stout, K. Y., Dong, W. P., Mainsah, E. (1993) A Proposol for Standardisation of Asserment of Three–

Dimensional Mikro-Topography-Part 1. Snrface Digitisation and Parametric Characterisation.

Birmingham: The University of Birmingham.

[12] Chen, X., Chen, G. (2009) On the thermally induced cracking of a segmented coating deposited on the

outer surface of a hollow cylinder, 9 (203), 1114 – 1120, Surface and Coat. Technol.