Engineering, Energy, Transport AIC

Muzychuk Vasyl – PhD, Associate Professor of the Department of “Technological Processes and Equipment of Processing and Food Productions” of the Vinnytsia National Agrarian University (3 Solnechnaya St, Vinnytsia, 21008, Ukraine, e-mail: wasil@vsau.vin.ua).   
Vitaliy Komaha - Candidate of Technical Sciences, Senior Lecturer of the Department of Agroengineering and Technical Services of the Vinnytsia National Agrarian University (3, Solnyshchaya St., Vinnitsa, Ukraine, 21008, e-mail: komacha@vsau.vin.ua).
Oleksii Tokarchuk – PhD, Associate Professor of the Department of “Technological Processes and Equipment of Processing and Food Productions” of the Vinnytsia National Agrarian University (3, Solnyshchaya St., Vinnytsia, 21008, Ukraine, e-mail: tokarchuk@vsau.vin.ua ).
Oleksandr Kukharchuk - engineer for repair of maintenance and diagnostics of agricultural machinery TITAN MACHINERY UKRAINE (Vatutina, 172, Vinnytsia, 21000, +380682134829)

On the basis of the engineering practices of the last 3-4 decades, it is known, tested and proven that, while mathematical models provide reliable descriptions of processes, cycles or physical phenomena, in theoretical research the theory of small deviations is comprehensively preferable to any experiment on regulating characteristics.
Considering the fact that all parameters and characteristics are sometimes interconnected by nonlinear dependences, it is impossible to distinguish the influence of a specific parameter on the sought-for value, and can be even hazardous if the determinant argument or its derivative has extreme values.
The role of mathematic simulation to determine the residual lifetime of the fuel injection equipment of diesel engines was established. It was also noted that for a reliable description of the processes going on in the fuel injection equipment it is advisable to use the method of small deviations.  
The mathematical model is based on the known physical laws that describe the interdependence of the two groups of parameters: engine variables and performance parameters - both within the groups and between them. The transition of classical differential equations describing the processes of fuel supply and injection taking into account fuel leaks in precision pairs to the equations with small deviations of parameters is shown.
An analysis of correlations between the parameters of injection, fuel supply and fuel leakage was carried out and the most influential parameters were found. The influence coefficients are found and correlations between the influence coefficients and the corresponding parameters are constructed. We used the correlations found to describe the influence of the technical condition of precision pairs on the engine performance indicators. The correlations between the change in injection patterns and small deviations of the parameters describing technical condition of precision pairs are also established.

[1]    Anisimov V. F. (1992). Diagnostirovaniye avtotraktornykh dizeley metodom raspoznavaniya obrazov po malym otkloneniyam parametrov. diss. doktora tekhn. nauk: 05.20.03. Moskva. [in Russian]
[2]    Nikolayenko, A.V., Khvatov, V.N., Obryadin, V.G. (1986). Prognozirovaniye pokazateley nadezhnosti toplivnoy apparatury po rezultatam nezavershennykh ispytaniy. Nauchn. tr. LSKhI. t. 300. L.: LSKhI. 8–12. [in Russian]
[3]    Muzichuk, V.І., Ryaboshapka, V.B., Burdeyniy, O. (2012). Zastosuvannya chiselnikh metodіv pri doslіdzhennі teplovikh protsesіv na matematichnikh modelyakh. Zb. nauk. pr. VNAU. Serіya: Tekhnіchnі nauki. Vіnnitsya: VNAU. Vip. 10, 2(59). 145–148. [in Ukrainian]
[4]    Anisimov, V.F., Muzychuk, V.I., Slobodyan, S.M. (2015). Matematicheskaya model vpryska topliva v malykh otkloneniyakh dlya opredeleniya ostatochnogo resursa dizelnoy toplivnoy apparatury. Zbіrnik naukovikh prats VNAU. Serіya: Tekhnіchnі nauki. Vіnnitsya. 1(89), 1. 68–75. [in Russian]
[5]    Anisimov, V.F., Muzychuk, V.I., Palamarchuk, I.P., Kovaleva, I.M. (2015). Vliyaniye tekhnicheskogo sostoyaniya pretsizionnykh par na effektivny pokazateli dizelya. Zbіrnik naukovikh prats VNAU. Serіya: Tekhnіchnі nauki. Vіnnitsya. 1(89), 2. 8–15. [in Russian]
[6]    Chernyshev, G.D., Malyshev, A.A., Khanin, N.S., Arshinov, V.D., Reznikov, M.L. (1974). Povysheniye nadezhnosti dizeley YaMZ avtomobiley KrAZ. M: Mashinostroyeniye. [in Russian]
[7]    Krugov, V.I., Rybalchenko, A.G. (1978). Regulirovaniye turbonadduva D.V.S. M.: Vysshaya shkola. [in Russian]
[8]    Lyshevskiy, A.S. (1971). Raspylivaniye topliva v sudovykh dizelyakh. L.: Sudostroyeniye. [in Russian]
[9]    Stanislavskiy, L.V. (1983). Tekhnicheskoye diagnostirovaniye dizeley. Kiyev-Donetsk: Vishcha shkola. Golovne vid-vo. [in Russian]
[10]    Grigoryev, M.A., Slabov, E.P. (1972). Issledovaniya kriteriyev predelnogo sostoyaniya dizelya. "Avtomobilnaya promyshlennost", 12. 8–10. [in Russian]
[11]    Popov A. (1981). Proyektirovaniye i issledovaniye toplivnoy apparatury dlya perspektivnogo malolitrazhnogo dizelya MEMZ [Otchet po NIR. gos. reg. № 79034996]. Voroshilovgrad. VMI. chast I. [in Russian]
[12]    Platonov, V.F. (1989). Polnoprivodnyye avtomobili. M.: Mashinostroyeniye. [in Russian]
[13]    Astakhov, I.V., Trusov, V.I., Khachiyan, A.S. (1972). Podacha i raspylivaniye topliva v dizelyakh. M.: Mashinostroyeniye. [in Russian]
[14]    Pizintsali, L.V. (2000). Vliyaniye izmeneniya geometricheskikh razmerov i regulirovochnykh parametrov toplivnoy sistemy na kolebatelnyy protsess pri vpryske topliva. Odessa.: Izd. OGMA. NTS, 5. 73–75. [in Russian]
[15]    Anisimov, V.F., Barsukov, S.I., Pizintsali, L.V., Rogacheva, E.V. (2002). Nadezhnost dizeley. Ch. 1. Odessa: OISV. [in Russian]
[16]    Zhdanovskiy, N. S., Nikolayenko, A.V., Alyapy, V.G. (1978). Uskorennyye ispytaniya raspylitelnoy forsunki na iznashivaniye. Nauchn. trudy. LSKhI. tom 345. L.: LSKhI. 14–19. [in Russian]
[17]    Antipov, V.V. (1972).I znos pretsizionnykh detaley i narusheniye kharakteristik toplivnoy apparatury dizeley. M.: Mashinostroyeniye. [in Russian]
[18]    Bobrov, V.F. (1960). Issledovaniye vliyaniya iznosa plunzhernykh par na vprysk topliva. Tr. KhNIIZhTA. 2 vyp. XXXV. 20–32. [in Russian]
[19]    Muravyev, V.P., Kulakov, V. (1981). Chislennyye issledovaniya matematicheskoy modeli fakela topliva v dizelnom dvigatele. TsNIITEI tyazhmash. VINKTI, 5. 81. [in Russian]
[20]    Kulakov, V.A., Muravyeva, V.P. (1980). Chislennoye issledovaniye matematicheskoy modeli fakela topliva v dizelnom dvigatele. Tyumen.. 210 s. Rukopis predstavlena Tyumens. industr. inst-m. Dep. v TsNIITEI tyazhmash. 24 dek. №665. [in Russian]
[21]    Selivanov, A.I. (1971). Osnovy teorii stroyeniya mashin. M.: Mashinostroyeniye. [in Russian]
[22]    Modelirovaniye i eksperimentalnyye issledovaniya rabochikh protsessov toplivnoy apparatury i dizelya (1985). [Otchet po NIR Odesskogo politekhnicheskogo instituta. deponirovannyy v VNTI tsentr. gos. reg. №1830066/inv. №0280007387]. [in Russian]
[23]    Borshchevskiy, Yu.T., Miroshnichenko, A.F., Pogodayev, L.I. (1980). Povysheniye kavitatsionnoy stoykosti dvigateley vnutrennego sgoraniya. K.: Vishcha shkola. [in Russian]
[24]    Anisimov, V.F. (1986). Analiz ostatochnogo resursa dizeley statisticheskimi metodami. K.. 22 s. Dep. v UkrNIINTI. 60. [in Russian]
[25]    Pizintsali, L.V. (2001). Upravleniye vykhodnymi parametrami dizelya putem izmeneniya kharakteristik vpryska topliva. MONU. Vestnik KhGTU, 1(10). 351–354. [in Russian]
[26]    Muzychuk, V.I., Anisimov, V.F. (2012). Orhanizatsiia robit pidpryiemstv tekhnichnoho obsluhovuvannia. Navchalnyi posibnyk. Vinnytsia: FOP Rohalska I.O. [in Ukrainian]