Issue №: 1(120)
The journal solves the problems of creation and improvement of machinery and technologies for agriculture: 131 - Applied Mechanics, 132 - Materials Science, 133 - Industrial Engineering, 141 - Power Engineering, Electrical Engineering and Electromechanics, 208 - Agricultural Engineering.
RESEARCH OF SURFACE PLASTIC DEFORMATION UNDER HYDRO-IMPULSE INFLUENCE
Inna Telyatnuk – postgraduate of Vinnytsia National Agrarian University (3, Solnychna st., Vinnytsia, 21008, Ukraine, e-mail: inna201098@gmail.com, https://orcid.org/0000-0002-2998-1506).
Increasing requirements for modern machines necessitates the use of new equipment and the improvement of existing equipment. Methods and techniques aimed at improving its operational and quality characteristics. One of the areas of improvement is the method of surface plastic deformation, which qualitatively affects the overall reliability of the product.
However, surface plastic deformation does not allow for the development of a schematic diagram and a general-purpose device that can be used to strengthen a wide range of agricultural machinery parts.
Differences in the physical and mechanical properties of the materials of manufactured parts, their weight, dimensions, longitudinal and transverse stiffness, condition or position, hardening process, type of production and other factors in each specific case force designers and technologists to find reasonable options for designing new devices for processing parts by surface plastic deformation for ensuring high technical and economic indicators. Therefore, the development of surface plastic deformation devices and the improvement of existing equipment are urgent scientific and engineering tasks.
The introduction of modern methods and tools in the development of mechanical engineering ensures an increase in the reliability of parts and products in general, as well as a reduction in the cost of production.
This article describes the compaction of metal powders as a technological operation, as a result of which powder blanks are formed. The equipment for vibropressing of powder blanks is considered and compared. Technical processes of basic vibration and vibration impact are presented.
The methods and schemes of implementation of vibropressing of powder materials are demonstrated. The classification of vibro-compaction processes according to the characteristics of vibration and vibration modes is analyzed.
[1] Paladijchuk, Yu.B., Telyatnik, I.A. (2022). Tipi i konstrukciyi vibrozbudzhuvachiv suchasnogo mashinobuduvannya. Vibraciyi v tehnici ta tehnologiyi, 4 (107), 26–35. [in Ukrainian].
[2] Veselovska, N.R., Paladijchuk, Yu.B., Telyatnik, I.A. (2022). Doslidzhennya mikrotverdosti poverhni cilindrichnoyi detali pri deformacijnomu protyaguvanni. Tehnika, energetika, transport APK, 3 (118), 31–42. [in Ukrainian].
[3] Iskovich-Lotockij, R.D., Ivanchuk, Ya.V. (2008). Pidvishennya efektivnosti rozvantazhennya materialiv pid diyeyu periodichnih udarnih impulsive. Vibraciyi v tehnici i tehnologiyah, 2(51), 8–11. [in Ukrainian].
[4] Iskovich-Lotockij, R.D., Ivanchuk, Ya.V. (2007). Doslidzhennya dinamiki procesu roboti universalnogo gidravlichnogo vibroudranogo privodu dlya rozvantazhennya transportnih zasobiv. Naukovi notatki. Mizhvuzivskij zbirnik (za napryamom «Inzhenerna mehanika»), 20, 184–187. [in Ukrainian].
[5] Miskov, V.P. (2015). Inercijnij vibropres-molot z elektrogidravlichnoyu sistemoyu keruvannya gidroimpulsnogo privoda dlya formoutvorennya zagotovok z poroshkovih materialiv : avtoref. dis. na zdobuttya nauk. stupenya kand. tehn. nauk : spec. 05.03.05 / Miskov Vadim Petrovich. pp. 22. Vinnicya, [in Ukrainian].
[6] Iskovych-Lototsky, R., Veselovska, N. (2018). Automatic system for modeling vibro-impact unloading bulk cargo on vehicles. Proc. SPIE 10808, Photonics Applications in Astronomy, Communications, Industry, and High-Energy Physics Experiments. 1080860 (1 October 2018). URL : https://doi.org/10.1117/12.2501526. (data zvernennya 30.09.2022) [in English].
[7] Iskovych-Lototsky Rostislav, Ivanchuk Yaroslav, Veselovsky Yaroslav, Gromaszek Konrad, Oralbekova Ayaulym (2018). Automatic system for modeling of working processes in pressure generators of hydraulic vibrating and vibro-impact machine. Proc. SPIE 10808, Photonics Applications in Astronomy, Communications, Industry, and High-Energy Physics Experiments 1080850 (1 October 2018). URL : https://doi.org/ 10.1117/12.2501532. (data zvernennya 30.09.2022) [in English].
[8] Iskovich-Lotockij, R.D., Ivanchuk, Ya.V., Veselovskij, Ya.P. (2014). Osnovi rezonansno-strukturnoyi teoriyi vibroudarnogo rozvantazhennya transportnih zasobiv. Nauka ta progres transportu. Visnik Dnipropetrovskogo nacionalnogo universitetu zaliznichnogo transportu im. akademika V. Lazaryana, 5 (53), 109–118. [in Ukrainian].
[9] Matysiak S., Pusz P. (1985). Axisummetric bousinesg problem for a granular hal. Bulletin of Polish Academie of Scienes, Technical Sciences, 33 (7/8), 351–358. [in English].
[10] Zolotarevskaya, D.I. (2011). Mathematical simulation and calculation of the soil compaction under dynamic loads. Eurasian Soil Science, 44 (4), 407–416. [in English].
[11] Li A., Dai F., Xu N., Gu G., Hu Z. (2019). Analysis of a Complex Flexural Toppling Failure of Large Underground Caverns in Layered Rock Masses. Rock Mechanics and Rock Engineering. URL : https://doi.org/10.1007/s00603-019-01760-5. (data zvernennya 01.10.2022). [in English].
[12] Debeleac, C., Nastac, S. (2014). Stochastic Approaches of Nonlinear Model-Based Simulations for Vibratory Compaction Process. PAMM, 14 (1), 749–750. [in English].
About journal
The magazine "Engineering, Energy, Transport AIC" is included in the list of scientific professional editions of Ukraine on technical sciences
(Category "Б", Order of the Ministry of Education and Science of Ukraine dated 02.07.2020 №886)
According to the decision of National Council of Television and Radio Broadcasting of Ukraine from 25.04.2024 No. 1337 the scientific journal «Engineering, Energy, Transport AIC» has the ID of the Media R30-05173.
The journal "Engineering, Energy, Transport AIC" is indexed according to the following databases and catalogs:
Certificate of state registration of mass media: No. 21906-11806 P dated 03/12/2016.
Founder of the journal: Vinnytsia National Agrarian University
Type of publication: journal
Kind of publication: scientific
Publication status: domestic
Year of foundation: 1997
Periodicity: 4 times per year
Volume: 18-20 conv. print. sheet (А4)
ISSN: 2520-6168 (print version), (online version)
Language of publication: (mixed languages) Ukrainian, English
The sphere of distribution and category of readers: national, foreign, faculty, scientists, entrepreneurs.
The periodical edition is included to the List of scientific professional publications of Ukraine on technical sciences, approved by order of the Ministry of Education and Science of Ukraine in 05.16.2016, No. 515.
The journal "Engineering, Energy, Transport AIC" is included in the "Catalog of Ukrainian Publications".
Subscription to the journal can be issued in each post office. The subscription index is 99720.
Technology, energy, agriculture transport AIC is a scholarly professional journal with a long-standing history and stable academic tradition, reflecting the evolution of engineering and technical sciences within the agro-industrial sector of Ukraine.
The journal was founded in 1997 under the title Bulletin of Vinnytsia State Agricultural Institute. According to the Resolution of the Presidium of the Higher Attestation Commission of Ukraine dated September 11, 1997, the publication obtained the status of a professional scientific journal, which enabled the publication of the main results of doctoral and candidate dissertations in technical sciences. From its inception, the journal positioned itself as an academic platform for addressing current issues of mechanization, electrification, and technical support of agricultural production.
During 2001–2014, the journal was published under the title Proceedings of Vinnytsia National Agrarian University. Series: Technical Sciences (State Registration Certificate of Print Media KV No. 16644-5116 PR dated April 30, 2010). Throughout this period, a systematic approach to the selection and peer review of scientific manuscripts was established, the thematic scope of publications was expanded, and continuity of scientific directions as well as the development of sectoral engineering schools was ensured.
Since 2015, the journal has been published under its current title, Technology, energy, agriculture transport AIC (State Registration Certificate No. 21906-11806 R dated March 12, 2016). The change of title reflected the expansion of the journal’s thematic coverage and its orientation toward interdisciplinary research in mechanical engineering, energy systems, electrical engineering, transport technologies, automation, and digital solutions for the agro-industrial complex.
The journal consistently adheres to the principles of open science. All published materials are distributed under the Creative Commons Attribution 4.0 International License (CC BY 4.0), ensuring open access to research results provided proper attribution to the authors and the original publication is maintained.
At present, Technology, energy, agriculture transport AIC is an authoritative professional scientific journal (Category B), providing a platform for the publication of fundamental and applied research results, promoting the integration of education, science, and industry, and contributing to the advancement of engineering and technological support of the agro-industrial complex of Ukraine.
