Engineering, Energy, Transport AIC

Nataliia Veselovska – Doctor of Technical Sciences, Full Professor, Head of the Department of Machines and Equipment of Agricultural Production of Vinnitsa National Agrarian University (3 Soniachna St., Vinnytsia, Ukraine, 21008, e-mail: wnatalia@ukr.net, https://orcid.org/0000-0001-9399-6721).
Yuriy Paladiychuk – Candidate of Science (Engineering), Associate Professor of the Department of Agroengineering and Technical Service of Vinnitsa National Agrarian University (3 Soniachna St., Vinnitsa, 21008, Ukraine, e-mail: rewet@vsau.vin.ua, https://orcid.org/0000-0003-4257-9383).
Inna Telyatnuk – postgraduate of Vinnytsia National Agrarian University (3, Solnychna st., Vinnytsia, 21008, Ukraine, e-mail: inna201098@gmail.com).

It is known that when processing plastic materials by cutting, chip grinding is a serious problem. The formation of a stable, strong draining chip is a sign of low machinability of the material of the part and requires the use of special means and methods that would ensure the separation of the chip or allowance that is cut.
This issue is especially relevant in the case of cutting drawing as a low-speed process, which is characterized by intensive overgrowth and a high coefficient of chip shrinkage, and therefore the strength of the latter. Today, there are a number of original developments of several scientific schools, which implement the idea of preliminary division of the allowance during drawing by creating a network of technological chip-splitting grooves.
The process of internal drawing, in particular drawing of round deep holes, must necessarily take place under conditions of forced chip separation or allowance. At the same time, the so-called transverse division of the chips, i.e., division along the perimeter of the hole, is usually carried out due to structural elements on the broach teeth and today is not too difficult a problem. However, there are certain reserves in this direction as well, in particular those related to increasing the stability of the tool.
This article considered the technological function of the reliefs, which consists in the forced division of the cut allowance with contour grooves. An analysis of the advantages and disadvantages of the most common processes for obtaining round holes in hollow blanks and parts is carried out. The essence of the group (progressive, variable) stretching scheme is described.
Typical combined extension tools are considered. Given formulas for calculating the dimensions of chip grooves. The first component р of the change in the diameter of the hole and the outer diameter of the workpiece after each of the combined drawing operations is characterized.

[1]    Sereda, L.P., Paladijchuk Yu.B., Budyak R. V. (2012). Vpliv disiparativnih vlastivostej materialiv protyazhnogo instrumentu na yakist obrobki gilz gidrocilindriv. Vibrations in engineering and technology, 2 (66). 87 – 89. [in Ukrainian].
[2]    Paladiichuk, Y. (2021). Study of characteristics of growth formation after deformation strength during deforming strength. Architecture Medical sciences Technical science Physics and mathematics. 2 (89). 30–35. [in English].
[3]    Shejkin, S.Ye., Studenec, S.F., Melnichenko, V.V., Melnichenko, Ya.V. (2016). Tehnologiya vidnovlennya kardannih valiv z zastosuvannyam gradiyentnogo deformacijnogo zmicnennya. Visoki tehnologiyi v mashinobuduvanni, 1 (26). 118–125. [in Ukrainian].
[4]    Posviatenko E., Posviatenko N., Budyak R., Shvets L., Paladiichuk Y., Aksom P., Rybak I., Sabadach B., Hryhorychen V. (2018). Influence of a material the technological factors on improvement of operating properties of machine parts by reliefs and film coatings. Eastern-European Journal of Enterprise Technologies, 5/12 (95). P. 48–56. [in English].
[5]    Paladijchuk, Yu.B., Kordonskij, V.A. (2020). Obgruntuvannya mehaniki rujnuvannya struzhki pri protyaguvanni cilindrichnih poverhon z pripuskom. Vibrations in engineering and technology, 4 (99). 73–84. [in Ukrainian].
[6]    Paladiichuk, Y. (2019). Forming of makrorelefiv is at reaching of internal surfaces of cylinder purveyance of power hydrocylinders. Modern engineering and innovative technologies, 10 (1). 74–79. [in English].
[7]    Skorkin, A.O., Kondratyuk O.L., Shelkovij O.M., Permyakov O.A. (2017). Pidvishennya efektivnosti protyaguvannya za rahunok kosokutnogo rizannya v zoni deformuvannya. Mashinobuduvannya, 20. 41–47. [in Ukrainian].
[8]    Nemyrovskyi, Ya., Shepelenko, I., Posviatenko, E., Tsekhanov, Yu., Polotnyak, S., Sardak, S., Paladiichuk, Y. (2020). Desining the structures of solid-alloy elements for broaching the holes of significant diameter based on the assessment of their strength. Eastern-European Journal of Enterprise Technologies, 3 (7-105). 57–65. [in English].
[9]    Bandura, V.M., Budyak, R.V. (2014). Doslidzhennya fiziko-mehanichnih vlastivostej poverhni gilz pislya protyaguvannya. Vostochno-Evropejskij zhurnal peredovyh tehnologij, 1.5 (67). 38-40. [in Ukrainian].